|
|
WEG Shark Drive Variable
Frequency Drives
 The
WEG Shark Variable Frequency Drive is a all stainless steel NEMA 4X and is
designed to complement the ruggedness of WEG's Shark Motor Product Line. The
WEG Shark line is ideal for high pressure hose wash down and corrosive
applications such as food processing and pharmaceutical industries. With the
Shark triple control capability (Volts/Hertz, Sensorless or Closed Loop
Vector) and the ruggedness it succeed in any industrial application
environment.
Applications
- Pumps
- Fans / Blowers
- Conveyors
- Rollout tables
- Agitators
- Mixers
Features
- NEMA 4X All Stainless Steel Enclosure
- V/Hz and Sensorless Vector Control
- Self Tuning
- Single and Three-phase input voltage
- 200-240V or 380-480V input voltage
- 150% current overload capacity
- Dynamic Braking transistor
- 32 bit RISC microprocessor controlled
PWM output
- 1.25 / 2.5 / 5 / 10 kHz adjustable
switching frequency
- Six isolated programmable digital inputs
- Three programmable relay outputs (250Vac
/ 1A)
- Two isolated programmable analog inputs
- Two programmable analog outputs
Protective features:
- Over current
- Motor overload
- Drive over temperature
- Output phase-to-phase and
phase-to-ground short circuit
- DC bus over and under voltage
- Power supply under voltage and phase
loss and external fault
Control features:
- Linear and "S" ramp acceleration
and deceleration
- Local/remote control
- DC braking
- Torque boost
- Motor slip compensation
- Electronic pot
- Preset speeds
- Adjustable V/Hz profile
- Maximum and minimum adjustable
frequency limits
- Two skip frequencies
- Adjustable output current limit
- JOG, ride-thru and flying start
and PID regulator
Display readings:
- Motor speed
- Frequency, voltage, current
and torque
- Output power (kW)
- Four last faults
- Drive status
- Digital and analog I/O
status,hours powered and hours running
Ambient:
- 104ēF (40ēC), 3300 ft
(1000m) altitude, 90% humidity, non-condensing
Optional Features:
- Close loop vector
control
- RS-485 Serial
Interface
- Fieldbus Comm:
Profibus DP, DeviceNet or Modbus RTU
- Encoder buffered
output
- Additional digital
and analog I/O
Ordering Information and Accessories:
Shark Drive-NEMA
4X Enclosure
Single and
Three-Phase-230V
Three-Phase-230V
Three-Phase-230V -
460V
The WEG Shark Drive - Single
and Three-Phase-230V
WEG
CFW090006TDN4Z, WEG
CFW090007TDN4Z,
WEG
CFW090010TDN4Z
The WEG Shark Drive -
Three-Phase-230V
WEG
CFW090006TDN4Z, WEG
CFW090007TDN4Z, WEG
CFW090010TDN4Z, WEG
CFW090016TDN4Z
The WEG Shark Drive -
Three-Phase-230V - 460V
WEG
CFW090003TGN4Z, WEG
CFW090004TGN4Z, WEG
CFW090005TGN4Z, WEG
CFW090009TGN4Z, WEG
CFW090013TGN4Z, WEG
CFW090016TGN4Z
Contact our experienced variable
frequency drive specialists at Variable Frequency Drive Co
at 510-490-2187 to get your quote, place your order and arrange for
shipping. Our electrical specialists are standing by and ready
to help
| WEG Variable Frequency Drives & Soft
Starters
|
 |
WEG CFW-08 Plus ( 1/3-10HP) Variable
Frequency Drives
The new WEG CFW-08 Plus Series with engineering improvements and
the re-design of their successful uLine VFD'S have produced one of
the most compact and pack featured microdrives in the marketplace. The
features and options in a NEMA1 enclosure allows the CFW-08 to be used
in many applications. Read more about the
WEG CFW-08 Plus Variable Frequency Drives.
|
 |
WEG CFW-09 ( 1-500 HP) Variable
Frequency Drives
The CFW-09 Variable Frequency Drive offers the most
advance technology in drives for three-phase AC induction motors.
The Vectrue Technology and it significant advancement allowing
VFD's to combine V/F, Sensorless Vector and closed loop vector (with
encoder) all in one control product. A innovated new
feature named Optimal Braking was introduced to simplify
applications that require braking torque, by eliminating the need for
the dynamic braking resistor it means a simpler, more compact and
economic solution. Read more about the
WEG CFW-09 Variable Frequency Drives.
|
 |
WEG CFW-10 Plus ( 1/4 - 3HP)
Variable Frequency Drives
With the expansion to the CFW-10 Variable Frequency Drive
Product Line, three new HP rating (1,2 and 3 HP) and frame sizes (Sizes
2 and 3) will complement the existing ratings. The benefits of the
CFW-10 is its compact size, easily mounted package, with a simplified
keypad and bright LED readout, complete diagnostics and fully
programmable I/O. The key benefits to the WEG CFW-10 is that it control
three-phase AC motors with a single-phase AC input. Increase flexibility
and decreased costs are achieved by eliminating the need for a step-up
transformer to operate three phase 230V AC motors when only single-phase
115V or 230V are available. With the new products lines, a single-phase
120 VAC input voltage will produce three phase 230V to drive motors up
to 1 HP and single-phase 230VAC input voltage will control motors up to
3HP.The CFW-10 is a perfect solution for many industrial and commercial
applications. Read more about the
WEG CFW-10 Plus Variable Frequency Drives.
|
 |
WEG Shark Drive™ ( 1 - 10 HP)
Variable Frequency Drives
The WEG Shark Variable Frequency Drive is an ideal solution with
its Stainless Steel NEMA 4X enclosure for high pressure wash down and
corrosive environments and is designed to complement the enclosure
ruggedness of WEG's Shark Motor Product Line. The Shark Drive's complete
package combination of the CFW-09's triple control capability
(Volts/Hertz, Sensorless or Closed Loop Vector) matched with the Shark
Drive's NEMA4X enclosure rating allows the Shark Drive™ to succeed in
virtually all applications in any industrial environment.
Read more about the
WEG Shark Drive Variable Frequency Drives.
|
 |
WEG Combination Soft Starters-GPH
Series (5-500 HP)
The WEG Combination Soft Starter, GPH Series packages is a very
simple and is designed for quick installation and start up. This package
only requires an input and output motor connection. The GPH series is
built for ruggedness and reliability and with its NEMA 4/12 enclosure it
is ideal for dusty and wet applications. Read more about the
WEG Combination Soft Starters-GPH Series Controls.
|
 |
WEG Crusher Duty-TPH Series Soft Starters (
100-600 HP)
WEG TPH Series provides a complete and
cost effective AC motor starting and protection solution. The TPH are
designed to withstand the most demanding AC motor starting applications.
While exceeding the requirements for the highest starting torque
requirements, plus with it's NEMA 4/12 enclosure making it ideal for
wash down and harsh conditions application. A emergency direct-on-line
starting is available at a flip of a switch plus an AC3 full HP rated
bypass contactor and motor overload relay is standard in the TPH series
which provides full motor protection.
Read more about the
WEG Crusher Duty-TPH Series Soft Starters.
|
 |
WEG SSW-03 Series Soft Starters ( 50-1000 HP)
The SSW-03 provides a complete and cost
effective solution with a full microprocessor based control, making
adjustments easy with the keypad start-up and still provides complete
motor protection. With the pump control feature which prevents running
pumps at no load and eliminates pipeline waterhammer.
Read more about the
WEG SSW-03 Series Soft Starters.
|
 |
WEG SSW-04 Series Soft Starters ( 5-75 HP)
The WEG SSW-04 are build for ruggedness
and reliability and provides a complete solution. With it's full
microprocessor based control which allows easy adjustment with the
keypad start-up, and complete motor protection.. With the pump control
feature which prevents running pumps at no load and eliminates pipeline
waterhammer. Read more
about the
WEG SSW-04 Series Soft Starters.
|
 |
WEG SSW-05 Series Soft Starters ( 5-75 HP)
The WEG SSW-05 is a compact fully digital
soft starter with state-of-the-art DSP controller. With the digital
construction some of the benefits includes: optimum operations,
diagnostics capability and full protection of the motor. The Status
LED"s alert the user of the operational status and with the dipswitches
and potentiometers simplicity in set-up and operation is assured. The
simplicity and the micro size and ease of set up makes it a quick and
easy solution. Read more
about the
WEG SSW-05 Series Soft Starters.
|
 |
WEG SSW-06 Series Soft Starters ( 3-2,500 HP)
The SSW-06 is WEG's third generation Soft Starter line.
The keypad, with dual display, has red LED digits which provide visibility and make
programming easier. Integral bypass contacts eliminate heat dissipation once the
motor is at full voltage, which makes it extremely compact and allows for simple
integration into non-ventilated enclosures and replacement of electro-mechincal
starters in Motor Control Centers.
Read more
about the
WEG SSW-06 Series Soft Starters.
|
 |
|
Soft Start Drives start motors at lower
voltages, slowly ramping up to operation voltage, which reduces wear
on mechanical gears, chains, sprockets, belts and gearboxes.
|
