|
|
The WEG SSW-06 Series Soft-Starters are static starters intended to accelerate,
decelerate and protect three phase induction motors. The control of the voltage applied to the motor
by the means of the thyristors triggering angle variation, allows the soft-start to start and stop an
electric motor smoothly .
With adequate adjustments of the variables, the torque produced is adjusted to the needs of the load, so
the required current is going to be as low as possible for the starting procedure.
WEG Soft-Starter SSW-06 series, micro processed and full digital, are products with state-of-the-art
technology and have been produced to ensure the best starting and stopping performance of induction motors,
presenting themselves as a complete and low cost solution.
The human-machine interface allows easy adjustment of the parameters what helps commissioning and
operation. The built-in Pump Control function allows an efficient control over pumps, avoiding overshoots.
Applications
- Pumps
- Fans
- Blowers
- Compressors
- Agitators / Mixers
- Extruding Machines
- Injection & Blow Molding
- Grinders
- Conveyor Belts
- Hoist / Monorails
- Dryers / Washing Machines
- Cutting Machines
- Escalators
- ...and much more.
Features
- 208 - 600V, 50/60Hz input power supply
- Built-in run rated bypass contactor
- Duty cycle: 300% full load amps for 30 seconds, 10 starts per hour
- Voltage ramp or current limit start modes
- Detachable keypad with dual display (LCD and LED) and copy function
- 90-250Vac auxiliary control voltage
- 32 Bits RISC high performance microcontroller
- IP00 protected chassis enclosure
- Six isolated 24Vdc programmable inputs
- Three programmable relay outputs (2 amp - 250V)
- One 0 - 10Vdc programmable analog output
- One 4 - 20mA programmable analog output
- Motor PTC thermistor input
- RS-232 serial interface
- Adjustable acceleration and deceleration ramps (1 - 299 seconds)
- Adjustable pedestal voltage (25 - 90% of line voltage)
- Display readings: Motor current, voltage, kW and power factor, line voltage and frequency, four last fault trips, run and power-up timers
Protective features:
- Motor overload
- Over current and phase loss
- Motor imemdiate over and under current
- SCR over temperature and fault
- Line phase loss and phase sequence
- Line over and under voltage
Ambient:
- 32°F (0°C) to 131°F (55°C), 3300 ft (1000m)
altitude, 90% non-condensing humidity
Ordering
Information and Accessories:
SSWO6 - IP00 Protected
Chassis Enclosure -
Input Power
Supply: Three-Phase - 230V
SSW06 - IP00 Protected Chassis Enclosure - Input Power Supply: Three-Phase - 460V
SSW06 - IP00 Protected Chassis Enclosure - Input Power Supply: Three-Phase - 575V
Products Quick Reference
WEG SSW-06 Series Soft Starters -
SSWO6 - IP00 Protected Chassis
Enclosure
Input Power Supply:
Three-Phase - 230V
WEG
SSW060010T2257ESZ,
WEG
SSW060017T2257ESZ,
WEG
SSW060023T2257ESZ,
WEG
SSW060030T2257ESZ,
WEG
SSW060045T2257ESZ,
WEG
SSW060060T2257ESZ,
WEG
SSW060085T2257ESZ,
WEG
SSW060130T2257ESZ,
WEG
SSW060170T2257ESZ,
WEG
SSW060205T2257ESZ,
WEG
SSW060255T2257ESZ,
WEG
SSW060312T2257ESZ,
WEG
SSW060365T2257ESZ,
WEG
SSW060412T2257ESZ,
WEG
SSW060480T2257ESZ,
WEG
SSW060604T2257ESZ,
WEG
SSW060670T2257ESZ,
WEG
SSW060820T2257ESZ,
WEG
SSW060950T2257ESH1Z,
WEG
SSW060950T2257ESH2Z,
WEG
SSW061100T2257ESH2Z,
WEG
SSW061400T2257ESH2Z
WEG SSW-06 Series Soft Starters -
SSWO6 - IP00 Protected Chassis Enclosure
Input Power Supply:
Three-Phase - 460V
WEG
SSW060010T2257ESZ,
WEG
SSW060017T2257ESZ,
WEG
SSW060023T2257ESZ,
WEG
SSW060030T2257ESZ,
WEG
SSW060045T2257ESZ,
WEG
SSW060060T2257ESZ,
WEG
SSW060085T2257ESZ,
WEG
SSW060130T2257ESZ,
WEG
SSW060170T2257ESZ,
WEG
SSW060205T2257ESZ,
WEG
SSW060255T2257ESZ,
WEG
SSW060312T2257ESZ,
WEG
SSW060365T2257ESZ,
WEG
SSW060412T2257ESZ,
WEG
SSW060480T2257ESZ,
WEG
SSW060604T2257ESZ,
WEG
SSW060670T2257ESZ,
WEG
SSW060820T2257ESZ,
WEG
SSW060950T2257ESH1Z,
WEG
SSW060950T2257ESH2Z,
WEG
SSW061100T2257ESH2Z,
WEG
SSW061400T2257ESH2Z
WEG SSW-06 Series Soft Starters -
SSWO6 - IP00 Protected Chassis Enclosure
Input Power Supply:
Three-Phase - 575V
WEG
SSW060010T2257ESZ,
WEG
SSW060017T2257ESZ,
WEG
SSW060023T2257ESZ,
WEG
SSW060030T2257ESZ,
WEG
SSW060045T2257ESZ,
WEG
SSW060060T2257ESZ,
WEG
SSW060085T2257ESZ,
WEG
SSW060130T2257ESZ,
WEG
SSW060170T2257ESZ,
WEG
SSW060205T2257ESZ,
WEG
SSW060255T2257ESZ,
WEG
SSW060312T2257ESZ,
WEG
SSW060365T2257ESZ,
WEG
SSW060412T2257ESZ,
WEG
SSW060480T2257ESZ,
WEG
SSW060604T2257ESZ,
WEG
SSW060670T2257ESZ,
WEG
SSW060820T2257ESZ,
WEG
SSW060950T2257ESH1Z,
WEG
SSW060950T2257ESH2Z,
WEG
SSW061100T2257ESH2Z,
WEG
SSW061400T2257ESH2Z
Contact our experienced
variable frequency drive specialists at Variable
Frequency Drive Co at 510-490-2187 to get your quote, place your
order and arrange for shipping. Our electrical specialists
are standing by and ready to help
| WEG Variable Frequency Drives & Soft
Starters
|
 |
WEG CFW-08 Plus ( 1/3-10HP) Variable
Frequency Drives
The new WEG CFW-08 Plus Series with engineering improvements and
the re-design of their successful uLine VFD'S have produced one of
the most compact and pack featured microdrives in the marketplace. The
features and options in a NEMA1 enclosure allows the CFW-08 to be used
in many applications. Read more about the
WEG CFW-08 Plus Variable Frequency Drives.
|
 |
WEG CFW-09 ( 1-500 HP) Variable
Frequency Drives
The CFW-09 Variable Frequency Drive offers the most
advance technology in drives for three-phase AC induction motors.
The Vectrue Technology and it significant advancement allowing
VFD's to combine V/F, Sensorless Vector and closed loop vector (with
encoder) all in one control product. A innovated new
feature named Optimal Braking was introduced to simplify
applications that require braking torque, by eliminating the need for
the dynamic braking resistor it means a simpler, more compact and
economic solution. Read more about the
WEG CFW-09 Variable Frequency Drives.
|
 |
WEG CFW-10 Plus ( 1/4 - 3HP)
Variable Frequency Drives
With the expansion to the CFW-10 Variable Frequency Drive
Product Line, three new HP rating (1,2 and 3 HP) and frame sizes (Sizes
2 and 3) will complement the existing ratings. The benefits of the
CFW-10 is its compact size, easily mounted package, with a simplified
keypad and bright LED readout, complete diagnostics and fully
programmable I/O. The key benefits to the WEG CFW-10 is that it control
three-phase AC motors with a single-phase AC input. Increase flexibility
and decreased costs are achieved by eliminating the need for a step-up
transformer to operate three phase 230V AC motors when only single-phase
115V or 230V are available. With the new products lines, a single-phase
120 VAC input voltage will produce three phase 230V to drive motors up
to 1 HP and single-phase 230VAC input voltage will control motors up to
3HP.The CFW-10 is a perfect solution for many industrial and commercial
applications. Read more about the
WEG CFW-10 Plus Variable Frequency Drives.
|
 |
WEG Shark Drive™ ( 1 - 10 HP)
Variable Frequency Drives
The WEG Shark Variable Frequency Drive is an ideal solution with
its Stainless Steel NEMA 4X enclosure for high pressure wash down and
corrosive environments and is designed to complement the enclosure
ruggedness of WEG's Shark Motor Product Line. The Shark Drive's complete
package combination of the CFW-09's triple control capability
(Volts/Hertz, Sensorless or Closed Loop Vector) matched with the Shark
Drive's NEMA4X enclosure rating allows the Shark Drive™ to succeed in
virtually all applications in any industrial environment.
Read more about the
WEG Shark Drive Variable Frequency Drives.
|
 |
WEG Combination Soft Starters-GPH
Series (5-500 HP)
The WEG Combination Soft Starter, GPH Series packages is a very
simple and is designed for quick installation and start up. This package
only requires an input and output motor connection. The GPH series is
built for ruggedness and reliability and with its NEMA 4/12 enclosure it
is ideal for dusty and wet applications. Read more about the
WEG Combination Soft Starters-GPH Series Controls.
|
 |
WEG Crusher Duty-TPH Series Soft Starters (
100-600 HP)
WEG TPH Series provides a complete and
cost effective AC motor starting and protection solution. The TPH are
designed to withstand the most demanding AC motor starting applications.
While exceeding the requirements for the highest starting torque
requirements, plus with it's NEMA 4/12 enclosure making it ideal for
wash down and harsh conditions application. A emergency direct-on-line
starting is available at a flip of a switch plus an AC3 full HP rated
bypass contactor and motor overload relay is standard in the TPH series
which provides full motor protection.
Read more about the
WEG Crusher Duty-TPH Series Soft Starters.
|
 |
WEG SSW-03 Series Soft Starters ( 50-1000 HP)
The SSW-03 provides a complete and cost
effective solution with a full microprocessor based control, making
adjustments easy with the keypad start-up and still provides complete
motor protection. With the pump control feature which prevents running
pumps at no load and eliminates pipeline waterhammer.
Read more about the
WEG SSW-03 Series Soft Starters.
|
 |
WEG SSW-04 Series Soft Starters ( 5-75 HP)
The WEG SSW-04 are build for ruggedness
and reliability and provides a complete solution. With it's full
microprocessor based control which allows easy adjustment with the
keypad start-up, and complete motor protection.. With the pump control
feature which prevents running pumps at no load and eliminates pipeline
waterhammer. Read more
about the
WEG SSW-04 Series Soft Starters.
|
 |
WEG SSW-05 Series Soft Starters ( 5-75 HP)
The WEG SSW-05 is a compact fully digital
soft starter with state-of-the-art DSP controller. With the digital
construction some of the benefits includes: optimum operations,
diagnostics capability and full protection of the motor. The Status
LED"s alert the user of the operational status and with the dipswitches
and potentiometers simplicity in set-up and operation is assured. The
simplicity and the micro size and ease of set up makes it a quick and
easy solution. Read more
about the
WEG SSW-05 Series Soft Starters.
|
 |
WEG SSW-06 Series Soft Starters ( 3-2,500 HP)
The SSW-06 is WEG's third generation Soft Starter line.
The keypad, with dual display, has red LED digits which provide visibility and make
programming easier. Integral bypass contacts eliminate heat dissipation once the
motor is at full voltage, which makes it extremely compact and allows for simple
integration into non-ventilated enclosures and replacement of electro-mechincal
starters in Motor Control Centers.
Read more
about the
WEG SSW-06 Series Soft Starters.
|
 |
|
Soft Start Drives start motors at lower
voltages, slowly ramping up to operation voltage, which reduces wear
on mechanical gears, chains, sprockets, belts and gearboxes.
|
